Permeable Concrete Mix Across Yorkshire

We produce our permeable concrete using a specialist mix designed for driveway sub-bases, including resin-bound and tarmac surfaces. The mix contains a carefully controlled ratio of cement, coarse aggregate and water, with reduced fine material so open voids remain throughout the structure once cured. These interconnected voids allow rainwater to pass through the surface and soak down into the ground below, rather than pooling or running off.

We can include additives such as poly fibres, air-entraining agents or plasticisers depending on site conditions and required performance. We deliver the mix ready to pour, giving contractors a consistent, dependable product for domestic and commercial driveway projects across Yorkshire and Lincolnshire, whatever the scale.

We mainly use our permeable concrete beneath driveway sub-bases, supporting resin-bound and tarmac surfaces on domestic and commercial properties. Because the mix allows water to soak through into the ground rather than sitting on top, it suits properties in areas prone to surface flooding or heavy rainfall, reducing pressure on nearby drainage systems. It also works well on commercial surfacing projects, car parks and paths where consistent drainage matters long term.

For homeowners and contractors who also need standard mixes delivered to the same site, our Ready Mixed Concrete range covers everything from footings to floor slabs. Permeable concrete pairs well with these deliveries, giving a full solution for driveways that need both a stable base and reliable drainage performance.

Yes, we design our permeable concrete specifically for driveway sub-bases, including resin-bound and tarmac surfaces on domestic and commercial properties. It allows rainwater to soak through the surface and drain into the ground below, rather than pooling on top or running off toward the road.

This protects the driveway from damage caused by rain, frost, snow and ice, helping it last for decades without needing to be replaced or relaid. It also reduces surface flooding and takes pressure off nearby drainage systems. To have the correct volume mixed and delivered precisely for your driveway dimensions, our Volumetric Concrete service measures materials on site, cutting waste and reducing the risk of ordering too much or too little for the job.

Our permeable concrete reaches its design strength after 28 days of curing, matching the timeframe we use across all of our mixes. While it contains fewer fines than standard concrete to preserve drainage voids, we engineer the mix to support driveway sub-bases under resin-bound and tarmac surfaces for both domestic and commercial use.

Strength is balanced against permeability, so the finished surface stays firm and stable under vehicle loads and foot traffic without cracking or shifting over time. The open-structure design also resists damage from frost, snow, ice and heavy rainfall, helping the sub-base hold up for decades. This combination of durability and drainage performance makes it a dependable, long-term choice for driveway projects that need to handle standing water.

Our permeable concrete reaches its full strength after 28 days, the same curing period we use across all of our mixes. Initial setting and hardening happen much sooner, usually allowing light foot traffic within a few days of pouring, though the surface should be protected from heavy loads and vehicles until curing is complete.

Weather conditions can affect the exact timeline, so we can advise on realistic timings for your driveway sub-base project based on temperature and site conditions at the point of delivery. Because our permeable mixes contain fewer fines to preserve drainage voids, protecting the surface during the early curing stage helps maintain both strength and the open structure needed for effective long-term water drainage performance.

Depth depends on the surface being installed above it, ground conditions, expected traffic loads and local drainage requirements, so there's no single figure we can apply to every driveway. Domestic driveways under resin-bound or tarmac finishes typically need a shallower sub-base than commercial car parks or access roads carrying heavier vehicles.

Using our quick calculator on this page, you can enter length, width and depth to work out the volume required once a depth has been confirmed for your project. Getting the depth right matters for both strength and drainage performance, since a sub-base that's too shallow can affect durability under load. For guidance specific to your site and surface type, you can contact us directly for advice before ordering.

Our permeable concrete works well for commercial driveway and surfacing projects alongside domestic use. Car parks, access roads and paved commercial areas benefit from the same drainage properties as residential driveways, reducing standing water and easing pressure on site drainage infrastructure. We mix to BS 206 compliance standards, giving contractors and site managers confidence in consistent quality across larger commercial pours.

Durability under regular vehicle traffic makes it a practical long-term option for retail parks, offices and industrial sites looking to manage surface water without expensive drainage systems. Consider our C10 Concrete mix for lighter commercial applications such as pathways or non-structural areas where a lower-strength grade is appropriate alongside your permeable sub-base.

We can include several additives in our permeable concrete mix depending on site conditions and project requirements. Poly fibres improve crack resistance and add reinforcement without steel mesh, while air-entraining agents help protect the mix against freeze-thaw damage during colder months. A retarding agent slows setting time for larger pours or hot weather, and an accelerating agent speeds up curing when a faster turnaround is needed.

Plasticisers improve workability, making the mix easier to place and finish without adding extra water. Availability and suitability depend on the specific driveway or surfacing project, so we can advise on the right combination. For stronger structural support in load-bearing areas, our C20 Concrete mix suits small-scale structural work.

We don't set a minimum order volume for our permeable concrete, making it suitable for smaller driveway repairs as well as larger new-build projects. Minimum charges do apply on smaller loads, covering the cost of preparing and delivering a mixer to site regardless of quantity ordered.

Larger volumes reduce the cost per cubic metre, so it helps to calculate the exact amount needed using our quick calculator on this page before requesting a quote. Getting an accurate volume also avoids ordering too much or running short mid-pour, which can affect the finish and strength of the sub-base. For an exact figure covering your specific driveway dimensions, you can contact us directly by phone or request a free quote online.

Ordering our permeable concrete is straightforward. Use our quick calculator on this page to work out the volume needed based on length, width and depth, then request a free, no-obligation quote online or by phone. We're available Monday to Friday from 7 am to 5 pm and Saturday mornings from 7 am to 12 pm, with fast delivery typically available within 24 hours across Yorkshire and Lincolnshire.

There is no minimum order volume, although minimum charges apply on smaller loads. For projects that also need a general-purpose mix for footings, pathways or lightweight applications alongside your permeable sub-base, our C15 Concrete grade can be ordered at the same time to save on delivery costs.